Snow spray filling machine using guide

We all know that the snow spray filling machine needs maintenance and maintenance. How to use the snow spray filling machine? How many steps are there? Next, let's take a look at the answer.

lThe working process of the snow spray filling machine

lUse and operation of snow spray filling machine

lMaintenance and precautions of snow spray filling machine

The working process of the snow spray filling machine

The barrel filling line of the snow spray filling machine can be divided into three steps: washing, filling and capping according to its functions. The working process is as follows: The gap movement chain moves one station. At this time, the empty barrel is in an inverted state and the barrel mouth and barrel body are rinsed. There are four steps in the flushing process of the snow spray filling machine: the first is clean water; the second is disinfectant; the third is sterile water washing; the fourth is rinsed with sterile water; there is 20S time after washing Drain in a bucket. The clean bucket chain of the flushed snow spray filling machine turns down 45 degrees, the bucket slides out by itself, and then the top bucket cylinder turns the bucket down 45 degrees, placing the empty bucket in the filling position, waiting for filling. The filling valve of the snow spray filling machine is pushed into the barrel by the cylinder, and the automatic exhaust filling valve is opened one by one for filling. The filling time is set by the PLC and can be corrected according to the level of the liquid by using the multi-function buttons on the panel. Filling time to reach the best position. After filling to the liquid level, the excess water will return to the pure water tank through the automatic drain to reduce pure water waste. After the filling of the snow spray filling machine is finished, the filled barrel is pushed to the capping station by the barrel discharge cylinder, and the cap is pressed during the next step of snow spray filling, and the whole process is over.

Use and operation of snow spray filling machine

Before starting the snow spray filling machine, check whether the disinfection level, power supply and air pressure are normal; manually check whether the solenoid valves and cylinders are in good condition, whether the action is normal, whether the rotation of each pump is correct, and whether the air is exhausted. If abnormal conditions are found, the snow spray filling machine must be eliminated before production can be carried out.

During production, the snow spray filling machine will automatically perform washing, disinfection, filling, capping, and pressing without human interference. However, the operator must closely observe the status of each part, find problems, and promptly turn the snow spray filling machine to the automatic direction Manually to prevent accidents. When the chain position is wrong, manually push out the main shaft of the snow spray filling machine, and then push the chain to the normal position. Disinfectant should be added in time during work to prevent the pump from idling in an anhydrous state, and the seal is burnt.

After the production is over, the residual liquid in the pipeline of the snow spray filling machine should be discharged, the gas path and water source should be cut off, and the power supply should be turned off.

Maintenance and precautions of snow spray filling machine

The parameters in the PLC program of the snow spray filling machine have been adjusted properly before leaving the factory, please do not modify it by yourself. The water storage cup of the three-piece pressure regulating valve assembly of the gas circuit board of the snow spray filling machine needs to be filled with water once every shift. The method is: adjust the lower screw, it can drain by itself, and often add some thin viscosity engine oil to the oil mist. In order to ensure the service life of the cylinder of the snow spray filling machine. The throttle valve of each cylinder of the snow spray filling machine has been adjusted properly before leaving the factory. Before starting the working procedure of the production line, ensure that the air source pressure of the snow spray filling machine is 0.45-0.6Mpa, otherwise the system cannot work normally. When the equipment is out of use, turn off the power switch first, and then turn off the air source switch. Prevent water and other debris from entering the electric control box of the snow spray filling machine. The electrical system of the snow spray filling machine is well grounded to prevent malfunctions caused by external interference with the computer. Grease the rack and gear of the snow spray filling machine regularly. Adjust the tightness of the chain frequently.

From these excellent characteristics of the snow spray filling machine, it can be seen that snow spray filling machine plays a key role in the development of our related industries. If you want to view more product information about snow spray filling machine and Aerosol Filling Machine , please visit the website http://www.meitarmachine.com/ to learn more.